DEV Community

Cover image for Build Your Own Lora Gps Tracker

Posted on

Build Your Own Lora Gps Tracker

This post describes how to create your own GPS tracker using Pycom LoPy microcontrollers.
You will also learn how to build your own single-channel LoRa Nano Gateway.

Do you prefer guided details and explanations ? There is a video recording available from my technical talk at the IBM Developer Europe Crowdcast channel.

The architecure diagram below shows the different components we will cover in our setup.
A LoPy Node, used as a GPS tracking device, sending data to a LoRa Nano-Gateway.
The gateway itself is connected to 'TheThingsNetwork' via WiFi.
Finally we'll have Node-Red running in IBM Cloud which will pick up the MQTT messages from 'TheThingsNetwork', store those into a Cloudant database, and visualize the GPS data points on a map.

Architecture diagram

Hardware needed:

  • 1 LoPy as LoRa node + Antenna (868MHz/915MHz) + 3.7V Battery
  • 1 uBlox NMEA Serial GPS Module with Antenna
  • 1 LoPy as LoRa Nano-Gateway + Antenna (868MHz/915MHz)
  • 2 Pycom Expansion boards

References to the hardware can be found at

Software needed:

In order to program the 'LoPy' microcontrollers we will use 'Pymakr' - a plugin for Atom or Visual Studio Code :

The 'LoPy' from is a multi-network hardware module based on the ESP32 microcontroller. Most of the modules (functions and libraries) are built into MicroPython.

1. Setup a LoRaWAN Nano Gateway and connect to 'TheThingsNetwork'

The source code for the LoRaWAN Nano-Gateway can be found here:

Unzip the download file and then find the lorawan-nano-gateway folder under examples.

All details for setting up the Nano-Gateway can be found at:

This will guide you to defining a gateway on The Things Network, set the configuration parameters according to your region, uploading the code to the board and verifying it's operational within The Things Network console.
You can get an account for free at The Things Network. It serves as a registration point for our gateway as well as an integration point for our data packets we will send from our LoRa GPS Tracker node.

2. Setup a Lora Node with GPS tracker

Getting started with 'The Things Network':

Follow the instructions on 'The Things Network' to register and activate your 'LoPy' device.

There are two ways to activate via either OTAA (Over the Air Activation) or ABP (Activation By Personalization). OTAA is the preferred method, certainly if you have a lot of devices, but doesn't seem to be working with the LoRa Nano-Gateway.

Following sample code uses ABP activation and once the LoRa communication is active it will send 10 bytes as 10 seperate packets.

from network import LoRa
import binascii
import struct

lora = LoRa(mode=LoRa.LORAWAN)

dev_addr = struct.unpack(">l", binascii.unhexlify('XXXXXXX'))[0]
nwk_swkey = binascii.unhexlify('XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX')
app_swkey = binascii.unhexlify('XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX')
# remove all the non-default channels
for i in range(3, 16):
# set the 3 default channels to the same frequency
lora.add_channel(0, frequency=config.LORA_FREQUENCY, dr_min=0, dr_max=5)
lora.add_channel(1, frequency=config.LORA_FREQUENCY, dr_min=0, dr_max=5)
lora.add_channel(2, frequency=config.LORA_FREQUENCY, dr_min=0, dr_max=5)
# join a network using ABP (Activation By Personalization)
lora.join(activation=LoRa.ABP, auth=(dev_addr, nwk_swkey, app_swkey))
# create a LoRa socket
s = socket.socket(socket.AF_LORA, socket.SOCK_RAW)
# set the LoRaWAN data rate
s.setsockopt(socket.SOL_LORA, socket.SO_DR, config.LORA_NODE_DR)
# make the socket non-blocking

for i in range (10):
    pkt = b'PKT #' + bytes([i])
    print('Sending:', pkt)
    rx, port = s.recvfrom(256)
    if rx:
        print('Received: {}, on port: {}'.format(rx, port))
Enter fullscreen mode Exit fullscreen mode

Now we have configured a LoRa node we should see the packets coming in via the console of the Nano-Gateway as well as within the console of 'TheThingsNetwork'.

Next we can add the code for reading the fixed GPS location data.
Sample code can be found here:

In the example we make use of the 'adafruit_gps' library and we only send a LoRa packet once we have a fixed GPS location.
This is all great but the data we receive are all bytes ! So how do we get this into a usable format ? We have to decode it !

Goto 'TheThingsNetwork'-console and select your application. Next select the tab 'Payload Formats' and define a decoder. Don't forget to save it.

function Decoder(bytes, port) { 
  return {
      GPSCoordinates: String.fromCharCode.apply(null, bytes)
Enter fullscreen mode Exit fullscreen mode

Now that we have a GPS tracker connected via LoRa, wouldn't it be nice to store this into a database and show the GPS data onto a map ?

For this, I chose to work with Node-Red within the IBM Cloud environment.
Easy to install, and completely free using a Lite account. You can signup for an account here.

By default the Node-Red flows are stored within a Cloudant database, so we can easily use that same database to store our GPS data.

You can find the example Node-Red flow here:

The GPS data is gathered from 'TheThingsNetwork' via MQTT and stored into Cloudant.
In order to get the data via MQTT from 'TheThingsNetwork' you will need to create/generate a new access key. Goto 'TheThingsNetwork'-console and select your application. You can find the access keys within the settings tab of your application. The generated key can be found at the bottom of the application overview page.

More details on usage of MQTT with 'TheThingsNetwork' can be found here:


This article should get you started with the basics of IoT using Lora communication.

If you want to see all this in action, there is a video recording available from my technical talk at the IBM Developer Europe Crowdcast channel
There I also show how to connect the Lora GPS tracker with a public Lora communication provider 'Proximus' in Belgium.

Are you thinking of other use cases for IoT using Lora ?

Top comments (0)